C&ENVENG 4107 - Prestressed Concrete Structures

North Terrace Campus - Semester 2 - 2020

Introduction to prestressed concrete-prestressing concepts; pre-tensioning and post-tensioning; full and partial prestress; the need for prestress; advantages and disadvantages; methods of prestressing. Forces imposed by prestressing (straight, draped and kinked tendon profiles). Load balancing. Introductory examples. Design requirements: strength and serviceability. Material properties. Design for serviceability: stress limits; serviceability criteria; determination of prestress and eccentricity; cable profiles; cracked section analysis; decompression and cracking moment; effect of cracking at service loads; short-term deflection calculations; crack control; design for strength: limit state design. Rectangular stress block. Ultimate moment capacity. Effect of non-prestressed steel; ductility; transfer strength; design for shear-effect of prestress on shear; stirrup design. Special problems in prestressing: losses; effect of creep and shrinkage; end block design-bursting and spalling forces in post anchorages; transmission lengths in pre-tensioned members. Statically indeterminate beams: introduction to continuous prestressed concrete beams; secondary moments.

  • General Course Information
    Course Details
    Course Code C&ENVENG 4107
    Course Prestressed Concrete Structures
    Coordinating Unit School of Civil, Environmental & Mining Eng
    Term Semester 2
    Level Undergraduate
    Location/s North Terrace Campus
    Units 3
    Contact Up to 4 hours per week
    Available for Study Abroad and Exchange Y
    Prerequisites C&ENVENG 3005
    Assessment Assignments, quiz, design project and a final examination - details at the start of Semester.
    Course Staff

    Course Coordinator: Dr Mohamed Ali Sadakkathulla

    Course Timetable

    The full timetable of all activities for this course can be accessed from Course Planner.

  • Learning Outcomes
    Course Learning Outcomes
    On successful completion of this course students will be able to:

     
    1 Calculate the acceptable design loading for prestressed beams using AS1100 and AS3600;
    2 Apply descriptive formula and code based understanding of the PSC design fundamentals;
    3 Apply PSC design and analysis through the design project and assignments;
    4 Analyse and design of simple PSC girders for flexure and deflections;
    5 Analyse and design of simple girders for shear & torsion; and
    6 Basic Analysis of continuous beams, anchorages etc.

     
    The above course learning outcomes are aligned with the Engineers Australia Stage 1 Competency Standard for the Professional Engineer.
    The course is designed to develop the following Elements of Competency: 1.1   1.2   1.3   1.4   1.5   2.1   2.2   2.3   2.4   3.3   3.5   

    University Graduate Attributes

    This course will provide students with an opportunity to develop the Graduate Attribute(s) specified below:

    University Graduate Attribute Course Learning Outcome(s)
    Deep discipline knowledge
    • informed and infused by cutting edge research, scaffolded throughout their program of studies
    • acquired from personal interaction with research active educators, from year 1
    • accredited or validated against national or international standards (for relevant programs)
    1-6
    Critical thinking and problem solving
    • steeped in research methods and rigor
    • based on empirical evidence and the scientific approach to knowledge development
    • demonstrated through appropriate and relevant assessment
    1-6
    Teamwork and communication skills
    • developed from, with, and via the SGDE
    • honed through assessment and practice throughout the program of studies
    • encouraged and valued in all aspects of learning
    1-6
    Career and leadership readiness
    • technology savvy
    • professional and, where relevant, fully accredited
    • forward thinking and well informed
    • tested and validated by work based experiences
    1-6
    Intercultural and ethical competency
    • adept at operating in other cultures
    • comfortable with different nationalities and social contexts
    • able to determine and contribute to desirable social outcomes
    • demonstrated by study abroad or with an understanding of indigenous knowledges
    1-6
    Self-awareness and emotional intelligence
    • a capacity for self-reflection and a willingness to engage in self-appraisal
    • open to objective and constructive feedback from supervisors and peers
    • able to negotiate difficult social situations, defuse conflict and engage positively in purposeful debate
    1-6
  • Learning Resources
    Required Resources


    1. Prestressed Concrete Structures, 3rd Edition R.F. Warner, A.K. Faulkes, & S.J.Foster, Pearson (Printice Hall), 2011. (hard copies available from Unibooks)

     2.Australian Standarrd AS-3600-Concrete Structures (Access/donload through library website)



    Recommended Resources
    Australian Standards for Concrete Structures AS-3600-2018
    Online Learning
    Lecture slides will be uploaded regularly on MyUNi.
  • Learning & Teaching Activities
    Learning & Teaching Modes


    This course uses a number of different teaching and learning approaches including:

    ·     Lectures

    ·     Problem-solving tutorials and assignments

    ·     Design Sessions

    ·     Self-directed activities

    ·     Design assignments

    .   Quizzes
    Workload

    No information currently available.

    Learning Activities Summary

    No information currently available.

  • Assessment

    The University's policy on Assessment for Coursework Programs is based on the following four principles:

    1. Assessment must encourage and reinforce learning.
    2. Assessment must enable robust and fair judgements about student performance.
    3. Assessment practices must be fair and equitable to students and give them the opportunity to demonstrate what they have learned.
    4. Assessment must maintain academic standards.

    Assessment Summary


    The assessment comprises of the following components: Assignments, quizzes and Design project report. Details will be announced in MyUni ASAP. Policy will also be available for late submission of assignment, missing quizzes etc.
    Assessment Summary

    1.Tutorials (4-5) (individual) weeks 2-12 Refer to MyUni-weighting -- 15% 
    2.Quizzes(Individual)Date TBA Refer to MyUni -weighting--30% 
    3.Design project(Individual)-Due in week-12 - weighting--55% 






    Assessment Detail

    No information currently available.

    Submission

    No information currently available.

    Course Grading

    Grades for your performance in this course will be awarded in accordance with the following scheme:

    M10 (Coursework Mark Scheme)
    Grade Mark Description
    FNS   Fail No Submission
    F 1-49 Fail
    P 50-64 Pass
    C 65-74 Credit
    D 75-84 Distinction
    HD 85-100 High Distinction
    CN   Continuing
    NFE   No Formal Examination
    RP   Result Pending

    Further details of the grades/results can be obtained from Examinations.

    Grade Descriptors are available which provide a general guide to the standard of work that is expected at each grade level. More information at Assessment for Coursework Programs.

    Final results for this course will be made available through Access Adelaide.

  • Student Feedback

    The University places a high priority on approaches to learning and teaching that enhance the student experience. Feedback is sought from students in a variety of ways including on-going engagement with staff, the use of online discussion boards and the use of Student Experience of Learning and Teaching (SELT) surveys as well as GOS surveys and Program reviews.

    SELTs are an important source of information to inform individual teaching practice, decisions about teaching duties, and course and program curriculum design. They enable the University to assess how effectively its learning environments and teaching practices facilitate student engagement and learning outcomes. Under the current SELT Policy (http://www.adelaide.edu.au/policies/101/) course SELTs are mandated and must be conducted at the conclusion of each term/semester/trimester for every course offering. Feedback on issues raised through course SELT surveys is made available to enrolled students through various resources (e.g. MyUni). In addition aggregated course SELT data is available.

  • Student Support
  • Policies & Guidelines
  • Fraud Awareness

    Students are reminded that in order to maintain the academic integrity of all programs and courses, the university has a zero-tolerance approach to students offering money or significant value goods or services to any staff member who is involved in their teaching or assessment. Students offering lecturers or tutors or professional staff anything more than a small token of appreciation is totally unacceptable, in any circumstances. Staff members are obliged to report all such incidents to their supervisor/manager, who will refer them for action under the university's student’s disciplinary procedures.

The University of Adelaide is committed to regular reviews of the courses and programs it offers to students. The University of Adelaide therefore reserves the right to discontinue or vary programs and courses without notice. Please read the important information contained in the disclaimer.